Friedemann Wagner GmbH
About us
Development, manufacturing, assembly and direct sales of pneumatic driven handling units. Rotary indexing tables, swivel units, lifting units, linear units and parallel-grippers as well as accessories are based on 45 years of experience. The products are available in different sizes and variants "off the shelf" or customer specific. The products can be mounted as modular system via center-rings and a grid system.
Products
Swivel Unit SES-6 - ❗️- with air- and signal-grommets
Pneumatic rotary actuator SES-6 👉 ...at booth B1-407 👈 ❗️ Full power in the end positions ❗️ 4 air ducts in the rotating turret ❗️ 4 signal ducts in the rotating turret ✅ Fixed, external stops via stop screws ✅ Repeatability +/- 0.01° ✅ Angle of rotation 0-190°, externally adjustable ✅ With shock absorber ❗️ Shock absorber failure detection possible ✅ Sensors for hollow stop screw ✅ Actual torque 6 Nm at 6 bar ✅ Jmax. 6,000 kgcm² ✅ Swivel times 0.35-2 s
modular system | column to fit in rotary indexer for simple assembly of other modules
✅ Hollow screw-in column ✅ For pneumatic rotary indexing tables ✅ For quick and easy installation of other automation modules ✅ Hollow, for media feedthrough for flange-mounted assemblies ✅ Movable, as it is attached to the rotary indexing table ✅ Secured in a fixed center hole using a fit and threaded ring ✅ Clamping block optional (accessory for Wagner grid spacing) ✅ Retrofittable (accessory) ✅ For pneumatic rotary indexing tables RSE-6 (ES-6) ✅ For pneumatic rotary indexing tables RSE-9 (ES-9) ❓ You may know our tables by a different label❓ ❗️We are manufacturers since 1979
Modular system -❗️- for easy automation
Example for needed motion sequence: ▶️ Lifting - Swiveling - Feeding - Gripping - Rotation on rotary indexing table Recommended modules; ✳️ Lifting unit HEK-4 ✳️ Swivel unit SE-4 with 4-way air grommets ✳️ Linear unit LSM-4 centrally mounted with ✳️ Adapter plate APL-4-N ✳️ Gripper PGM-38 ✅ Grid dimension with centering holes ✅ Centering rings (fit h6) ✅ Quick joining and assembly without drilling ✅ Adapter plates available as accessories
pick & place - kit in different strokes and functions
✅ Modular pick+place system ✅ Horizontal movement via linear unit LEN-6 ✅ Stroke lengths 100, 200, 300 or 400mm ✅ Vertical movement via vertical unit VEN-6 ✅ Stroke lengths 80, 120, 180, 240 or 300mm ✅ Intermediate position module for placing on a different level ✅ in suitable vertical stroke lengths 80, 120, 180, 240 or 300mm. ✅ Air and signal integration through the units to the mounted gripper optional ❗️System is already equipped with dampers and sensors ex works ❗️ ✅ Matching tripod in the accessories. ✅❗️ can be mounted on swivel unit SES-9❗️ ✅ Parallel gripper of the PGM series - see brochure link attached.
pneumatic driven ❗️ mini linear unit ❗️ with mini gripper
✅ LSM-3 – our mini linear slide ✅ for the automation of small workpieces ✅ pneumatic driven ✅ 3 stroke lengths (20, 35 and 50 mm) ✅ with or without mounted shock absorbers ❗️2 guide carriages (sealed ball bearing guides) ❗️recommended payload of 0.5 kg is 5 times higher than the item weight ✅ hardened stop screws ✅ external stops ❗️ repeat accuracy +/-0.01 mm ✅ stop screws for stroke adjustment ❗️ stop screws are hollow = sensor holder. ✅ no additional interfering dimensions, installation space is used optimally ♻️ little air consumption as small workpieces to be moved ♻️ little installation space ❗️ matching mini gripper (PGM-29) ✅ can be mounted by grid e.g. at the front of the head of the linear unit Technical data LSM-3 ✅ Stroke lengths 20 mm, 35 mm, 50 mm ✅ lifting force 11 N, retraction force 7 N ✅ Max. payload 0.5 kg ✅ Repeat accurracy +/-0.01 mm ✅ Stroke adjustable on both sides 15 mm ✅ Guide: 2 guide carriages (sealed recirculating ball bearing guide) ✅ Weight 60-100 g depending on stroke length ✅ Option: with mounted hydraulic shock absorbers ✅ Centering system – e.g. B. to accommodate mini gripper PGM-29 Technical data parallel gripper PGM-29: ✅ Stroke per jaw 2 mm ✅ Repeat accurracy +/-0.02 mm ✅ Finger length max. 15 mm ✅ Clamping force at 6 bar: 16 N ✅ Recommended workpiece weight 0.13 kg (force-fitting) ✅ own weight 0.025 kg ✅ Query option via sensors
Mini swivel unit ❗️ pneumatic driven ❗️gripper PGM-29
✅ extremely compact swivel unit ✅ 0-190° adjustable ✅ for small installation spaces and small workpieces ✅ effective torque of 0.3 Nm ✅ 3.5 kgcm² mass moment of inertia ✅ depending on requirements with | without hydraulic dampers ❗️ External stop screws = full torque in the end position ✅ Repeat accuracy of ± 0.01° ❗️ hollow stop screw = place-holder for sensor ❗️ see image: despite the smallest dimensions, optionally with 2 air grommets ✅ Air grommets supplies parallel gripper through the rotating unit ♻️ Short compressed air paths, no torsions ♻️ small workpieces need little air consumption ♻️ small workpieces need little space Technical data parallel gripper PGM-29: ✅ Stroke per jaw 2 mm ✅ Repeat accuracy +/-0.02 mm ✅ Finger length max. 15 mm ✅ Clamping force at 6 bar: 16 N ✅ Recommended workpiece weight 0.13 kg (force-fitting) ✅ own weight 0.025kg ✅ query option via sensors
Rotary indexing tables ❗️4 sizes ❗️manufacturer
❓ You may know our tables with a different label❓ ❗️We are manufacturers since 1979 ✅ pneumatic + manual rotary indexing tables ✅ standard products from stock ✅ customer-specific projects/rotary indexing products ✅ integrated throttle for adjusting the table speed ✅ control via one (!) 5/2 valve possible ✅ various. sizes up to 70 kg clamping weight / 30 Nm torque ✅ hydraulic damping included ✅ monitoring by initiators possible ♻️ option: wear-free pneumatic damping for RSE-6/RSE-9 ✅ partitions 2 to 24, depending on variant ❗️ uneven divisions for RSE-6 or RSE-9 (e.g. 7 or 13) ✅ direction of rotation: right or left ✅ for RSE-3 and RSE-4: alternatively oscillating operation ✅ for RSE-3 and RSE-4: direction of rotation can be changed by the customer ❗️ for RSE-4 and RSE-6-M, partition can be changed by the customer (kit) ✅ for RSE-6 / RSE-9, fixed center hole ❗️ for RSE-4, air grommet to G1/8" in the plate center ✅ RSE-6-M = manual turning, automatic locking, pneumatic release
Manufacturer of pneumatic driven modules
Made in Germany We are manufacturer of precise and durable pneumatic handling modules, modular, in different sizes ✅ rotary indexing tables (pneumatic or manually driven) ✅ swivel units ✅ lifting units ✅ linear units ✅ parallel grippers ✅ accessories ✅ wide range program " off the shelf" ✅ customerspecific solutions. Brochures in "MEDIA" below are in German AND English language!! website: https://wagnerautomation.de/en brochures see here: https://wagnerautomation.de/en/downloads/ productfinder: https://wagnerautomation.de/en/productfinder/
Swivel Units - ❗️ a bit different than others
✅ Manufacturer of swivel units with full torque in the end position half! ✅ Angle of rotation adjustable from the outside using stop screws ✅ Screws are clamped after adjustment ❗️ hydraulic shock absorbers only decelerate - the stop is the screw itself ❗️ ❗️ repeat accurracy +/- 0,01° as not depending on gear❗️ ✅ hydraulic shock absorbers can be reached from the outside ✅ stop screw is hollow and serves as a holder for the sensor ✅ space-saving, all interfering edges on one side ❗️Design principle enables detection of a shock absorber failure ❗️ ✅ Air grommets in the rotating stop surface as variants ✅ electrical signal feedthrough for larger units (variants)
Parallel gripper PGM - simple, robust, reliable
✅ Parallel gripper PGM ✅ simple principle ✅ repeat accuracy at +/- 0.02mm ✅ always centering system ✅ open construction - dirt also can escape ✅ PGM can be blown out and lubricated when installed ✅ in various sizes with 2mm to 15mm stroke per jaw ✅ available from stock ✅ recommended workpiece weights @ PGM-29: 130g, @ PGM-140: 7.2 kg ✅ prompt-query via proximity switch (inductive, partly C-slot)
Rotary indexing table RSE-4 - can be changed in direction and partitions
✅ pneumatically driven rotary indexing table RSE-4 ✅ can be installed in any position ✅ partitions 2/3/4/6/8/12 and 24 ✅ direction of rotation L/R can be changed by the customer by converting kit. ✅ vontrol can be done via ❗️ONE ❗️ 5/2 control valve. ✅ adjustment of the rotation speed of the table via exhaust air throttle (integrated). ✅ Division kits for changing the partition by the customer ❗️ oscillating operation as an order variant or with a conversion kit ✅ effective torque of the table is 2Nm @6bar (theoretically 3.5Nm). ✅ max. dynamic load weight is 14kg, ✅ max. moment of inertia 175kcm2 ✅ repeat accuracy is +/-0.03mm @ D= 120mm
Linear unit with cross roller guides - ❗️more load on same space
✅ pneumatic driven linearslide LSK ✅ cross roller guides for precise absorption of high torque loads ✅ repeat accuracy +/- 0,01mm as external stop positions ✅ 2 sizes: LSK-4 and LSK-6 ❗️own guides in which the cages run reduce the installation space❗️ ❗️this enables us to install / use larger rollers ❗️ ❗️up to 50% higher forces compared to others in the same installation space❗️ ♻️ Our active contribution to sustainability and resource efficiency. LSK-4 -stroke length 20, 30, 45, 60, 75 or 90 mm -lifting force 45N @ 6 bar -recommended payload 3kg -available in version with/without mounted shock absorbers LSK-6 -stroke length 30, 50, 75, 100, 125, 150, 175 or 200 mm -lifting force 76N @ 6 bar -recommended payload 22 to 10 kg depending on stroke -available in version with/without mounted shock absorbers
Lifting unit with cross roller guides
✅ Lifting unit HEK-4 and HEK-6 ✅ Cross roller guides for precise absorption of high torque loads ✅ Cross roller guides diagonal to the base plate ✅ Repeatability +/- 0.01mm through external stops ✅ Stroke length can be influenced using the hollow stop screw ✅ Delivery condition with or without mounted shock absorbers ✅ Sensors for installation in the hollow stop screw (accessory) ✅ Unit can also be installed horizontally. HEK - 4 ✅ Lifting force 80 N ✅ Stroke lengths 10mm and 25mm HEK - 6 ✅ Lifting force 185 N ✅ Stroke lengths 25 and 50 mm
Power Pack ❗️ Swivel Unit SES-9 ❗️full torque in end-position
✅ Pneumatic rotary actuator SES-9 (swivel unit) ✅24 Nm torque (@ 6 bar) ✅ full torque in the end positions ✅ 0-190° adjustable from the outside ✅ max. moment of inertia 64,200 kgcm² (@ 6 bar) ✅ with hydraulic shock absorbers ex works ✅ optional: sensor can be screwed into the stop screw ✅ optionally available as variants with air / signal feedthrough ❗️ third position can be reached via additional module
manually driven rotary indexing table
✅ simple, reliable and cost-effective solution ✅ for partially automated (hybrid) workplaces ✅ for manual workstations with processing stations ✅ no provision of drive technology, safety technology, two-hand operation, etc. necessary. ✅ self-locking after manual rotation ✅ backlash-free indexing of the rotary indexing table ✅ unlock after machining the workpiece via pneumatic impulse ✅ manual rotation until the next division ✅ unlocking via 3/2 valve e.g. push button ✅ table is rounded, reduces the risk of injury ✅ four-point bearing of the plate enables any installation situation ✅ tilting moment: up to 300Nm ✅ plate already has mounting holes for workpiece or workpiece carriers ✅ end position query via M8 sensor ✅ factory-fitted direction of rotation anti-clockwise | can be ordered on the right ✅ can be ordered ex works in pitches 2|3|4|6|12. ❗️partition and direction of rotation can be changed by the user (conversion kit) ❗️flexible application options ❗️retention of the investment in equipment
compact rotary indexers RSE-3 and RSE-4
✔️pneumatic rotary switching units ✔️control with one valve ✔️position-independent operation ✔️hydraulic damping included ✔️direction of rotation clockwise or counterclockwise - convertible ✔️divisions 2|3|4|6|8|12 - with RSE-4 also 24 ✔️optional oscillating version
Wagner stop system - stop screw with sensor - damper only retards
✅ Adjust the stroke with the stop screw (screw in and out) ✅ Adjust the damping ➡️ the stop screw, not the damper, gives the stop position! ✅ Clamp the block with the stop screw and damper ✅ Insert the sensor into the hollow stop screw and adjust, fix it with the knurl
Construction kit | Centering system from Wagner
✅ Grid dimension with centering bores ✅ Centering rings (fit h6) ✅ Quick joining and assembly without drilling ✅ Adapter plates in the accessories
Rotary indexing tables ❗️ odd divisions possible
✅ Pneumatic rotary indexing tables RSE-6 + RSE-9 ✅ can be ordered in odd divisions, e.g. division 7❗️ or division 13 ❗️ ✅ basis of the function is the lateral locking of the table ✅ RSE-6: all integer partitions from 4 -18 ✅ RSE-9: all integer partitions from 4 -24 ✅ available with hydraulic or pneumatic damping