Exhibitor products

ABACUS EVO cabinet is suitable for different applications: Data Networking (data centers, networking and smart building) and Commercial Buildings (smart city and infrastructures). The profile that characterizes the uprights and crosspieces of the roof/bottom is unique, made of high-strength steel sheet (HSLA), closed with continuous fiber laser welding and free from sharp edges. The union of the entire structure is obtained by means of 8 high-strength screws. The individual parts that make up the cabinet are made of sheet steel, edged for high resistance to torsion. The static load of the structure is 1400Kg. The rack uses the new "OPEN VIEW" concept, which enhances the maximum internal visibility of the rack to fully highlight the equipment and the cabling system installed inside. This cabinet has different benefits: • Easy installation of ventilation units and cable entry from above • Easy cable entry • Complete range • Easy to use structure • Modularity

IO Link right to the absolute encoder

With the AC drives of the FDD 3000 series you can optimize your production process. Economical asynchronous motors can be precisely controlled with the low voltage AC drives. Thus, your motion application becomes more efficient and you save energy at the same time. The compact devices are available in 7 sizes. The 1- or 3-phase AC drives cover a power range from 0.37 to 90 kW. With an overload capacity of up to 180 %, the FDD 3000s are ideally suited for applications with short-term high torque requirements.

AC asynchronous motors can be found in many different applications - be it in industry, transport or even in private households. Single- or three-phased, designed in different sizes, AC synchronous motors are characterized by their simple and robust build. As long-term runners, they require very little maintenance, are long-lasting and cost-effective . Advantages of our AC motors: • Robust, low-maintenance design • Very cost-effective • Long lifetime • Easy control • Low noise • Compact design and different rotation directions • Can be combined with a variety of gearboxes as well as with speedometer and brakes

Accessories Document pockets, ground straps and plug sockets are just a few of the practical accessories available for switchgear cabinets.

Enhance shop floor operations with achtBytes' cloud-native condition monitoring. Utilize I0-Link for efficient data collection and processing in our IoT platform. Achieve real-time monitoring of machinery, access precise cloud data, boost efficiency, identify cost-saving opportunities, prevent downtimes, and optimize maintenance proactively. Elevate your operations with achtBytes. #IoT #ConditionMonitoring #OperationalEfficiency #peakshaving

- Convenient parameter assignment via Bihl+Wiedemann software suites - Transmission of up to 4 × 16 Bit Process Data in 1,27 ms - Up to 32 bytes of cyclic process data - 1 IO-Link Port Class A (BWU4748), Power supply of IO-Link ports out of ASi - 1 IO-Link Port Class B (BWU4088) - 2 IO-Link Ports, e. g.: 1 IO-Link Port Class A, 1 IO-Link Port Class B (BWU4077)

The AD-FM 300 GT (1-channel) and AD-FM 600 GT (2-channel) are freely programmable frequency/analog measuring transducers with integrated display unit. Due to its multifunctional processing of the input frequency and the up to 2 analog outputs (current/voltage) per channel or the evaluable digital outputs, the device is optimally suited for the display of instantaneous flow rates with simultaneous evaluable counting pulse output for water meters with main and sub meters. Especially for large water meters with bypass, a scaled summation is integrated in the AD-FM 600 GT. Both the instantaneous flows and the counted quantities are output. A low level suppression is shiftable. Application The main area of application is the through-flow measuring at water meters. Further applications are the measuring of rotation speed or energy consumption. Specific characteristics - 1 (AD-FM 300 GT) or 2 (AD-FM 600 GT) channels in just one housing - Inputs: NAMUR, contact, open collector, 3-conductor Opto, 24V activ - Analog outputs: each channel 1 current and 1 voltage (synchronous) - Digital outputs: relay respectively optocouple (puls function or limit contact) - Scaled summation and shiftable low level suppression - Programming directly on the device or free programming software - DIN rail mounting

The digital power and energy meter AD-LU 20 GT measures all standard values of the three-phase system (active-, reactive-, apparent-power, voltage, currents, harmonics, power factor etc.) and provides this via an Ethernet interface. The measured values can be read out via Modbus-TCP protocol. In addition, these measured values are displayed on an integrated small WEB server. The device can also be parameterized via this WEB server. The AD-LU 20 GT is also equipped with an RS485 interface. This RS485 interface with Modbus-RTU protocol is mainly suitable for connecting an external display (AD-MM 400), but can also be used to read data or parameterize. The current is fed via the front-mounted through-current converters, which can measure up to 20 A directly. However, additional current transformers for larger currents can also be connected at any time. It is possible to measure symmetrical or unbalanced 4-wire networks and symmetrically loaded 3-wire networks. Due to the integrated, efficient wide-range power supply, the device operates in a large supply voltage range and does not heat up very much.

The digital power converter AD-LU 40 GT measures all values of the three-phase power grid such as current, voltage, energy, active, reactive, apparent power and frequency and makes this data available via a fieldbus. The device is therefore ideally suited for integration into energy management systems. The ProfiNet variant contains a 2-port switch for direct forwarding to the next device. 3- or 4-wire networks can be measured. 4-wire networks may have balanced or unbalanced load. 3-wire networks must have balanced load. The AD-LU 40 GT is powered by its measuring voltage L1. However, a variant with separate supply terminals and wide-range power supply is also available (AD-LU 40-S GT). The current measurement takes place via the throughput converters attached to the front. For the measurement of higher voltages or currents, external converters can be connected at any time. LEDs on the front panel signal the operating state and the data traffic. The compact design and the high performance combined with low energy consumption allow it to be used in almost any application. In addition, the device has a front-sided RS485 interface to which, for example, the TFT display AD-MM 400 can be connected. Thus, without any great effort, all measured values can be displayed. Application Measurement and monitoring of all electrical characteristics in electrical systems. Detection of load profiles for energy management systems, e.g. ISO 50001. Recording the energy consumption of individual consumers. Monitoring of voltage quality variables, e.g. Harmonics. Attention: This is a Class A product according to EN 55011. Additional EMC actions may be necessary when used in small businesses or in residential areas. Specific characteristics - Fieldbus interface for PROFINET or PROFIBUS - RS485 interface for connecting a TFT display

Especially in power plant operations but also in many other switchgear areas, active power for the optimization and control of processes must be continuously measured. The power converter AD-LU 410 GT is always adapted to the individual case by means of plant-specific adaptations. Due to the fully analog design, fast power measurements are possible, e.g. the detection of short-time load changes. The nominal voltage, the power to be measured and the desired output signal are required by the customer. The exact power values are available as standard signal for further processing.

The AD-LU 650 GT is a digital measuring transducers for the acquisition of all measured variables in the three-phase network. In addition to the fundamental oscillations, the harmonics up to the 32nd harmonic are also measured for currents and voltages. In addition to the three phase currents, the current in the neutral conductor can also be measured. Any measured variable can be assigned to each analog output. Each digital output can be assigned its own function such as limit value monitoring or pulse output for an energy meter. All measured data can be read out via the Modbus-RTU interface. With an optional display device such as the AD-MM 400 FE or the AD-MM 500 FE, the data can be displayed and the device can be configured if necessary.

The AD-STVEX 710 GVD supply isolating amplifier is used for the intrinsically safe supply of a transmitter installed in the hazardous area. The supply isolation amplifier itself is installed as associated electrical equipment in the non-hazardous area, i.e. the safe area. The signal is galvanically isolated and transmitted to the non-hazardous area. The passive input also allows active signals from the hazardous area. The active current output, the current sink output and the voltage output facilitate the adaptation to the following signal input. The device can be operated at 24 V DC or 230 V AC. Application Supply of a transmitter in the hazardous area and galvanic isolation of the signal. Specific characteristics - Supply of a transmitter up to zone 0 (gas) or 20 (dust) - Active current output, current sink output and voltage output - Open-circuit detection according to Namur recommendation NE43 - Further parameters configurable via configuration software AD-Studio - Detachable, coded connection terminals - Zero and full scale adjustment possible via front panel keys

The AD-SW 3 GL is used to measure high AC currents, such as secondary currents from large current transformers (e.g. 0...5A AC). The device contains 3 measuring transformers for contactless measurement of all three phase currents. The lines to be measured are fed horizontally through the device. Three small signal outputs are available for evaluation, which represent the measured current. The three output signals are galvanically coupled but separated from the input and the supply with high isolation. The AC sine wave voltage outputs, which follow the input signal 1:1 up to the maximum bandwidth of the device, can be customized. The integrated wide range power supply allows a wide supply voltage range with low self-heating.

The isolation amplifier AD-TV 420 GVD serves the galvanic separation of analogue signals and of transmitter signals. When a 2-wire transmitter is connected, this will be supplied directly via a galvanically separated and current-limited supply voltage. All measuring ranges and outputs can be freely parameterized. This can be carried out via the optional operating panel AD-VarioControl or via the programming software AD-Studio. The wide bipolar input measuring range makes this buffer amplifier into the universal type for almost all applications in the area of standard signals and beyond. All supply ranges are covered with the wide range power pack. Application Amplification, transformation and electrical isolation of current or voltage signals Specific characteristics - bipolar current input (+/- 0,5 mA bis +/- 50 mA) - bipolar voltage input (+/- 1 V bis +/- 100 V) - Power supply for 2- / 3-wire transmitters - 2 bipolar current or voltage output - Operating module as an accessory - 23 mm narrow housing with detachable terminal clamp